Product Categories

Brand Categories

Active Speakers

Bowers & Wilkins active speakers

Active vs passive speakers: what’s the difference? Which is better?

In their simplest form, traditional stereo hi-fi systems consist of a source component, an integrated amplifier and a pair of passive speakers (bookshelf speakers or floorstanding speakers) . Pretty straightforward, right? The active speakers are all in-one.

But if you break down the signal path it can be split into a greater number of distinct sections, most of which are lumped together in this simple set-up.

What are passive speakers?

First, there’s a source component, which is the piece of kit that plays the music. This can be a CD player, music streamer, record player or even a computer or phone. Next we have a preamplifier section, this switches between sources and controls the volume level.

If you have a record player, you’ll also need a phono stage to increase the output from your cartridge to line level and equalise the signal before feeding it to the preamp circuit (we’ve omitted the phono stage from our diagram to keep things simple).

Its output has to pass through a crossover filter network that in a two-way speaker splits the signal into just high frequencies (to go to the tweeter) and everything else for the larger mid/bass unit.

If you have a three-way speaker, then the crossover splits the sound up into three parts – treble, midrange and bass. This crossover network doesn’t need a power source to work, and in that sense it is considered passive. That’s more or less the signal path in a conventional passive set-up.

What are active speakers?

In an active system things are the same until after the preamp stage. The signal from the preamp goes into an active crossover network. While this performs the same job as the crossover in the passive set-up it works at line level (around 2v) rather than speaker level (typically 15-35v).

Working at lower signal levels means the components used can be optimised for precision rather than power handling. Such a design would normally use active components, and on more sophisticated products, some form of signal processing (whether digital or not) to get the best out of the drive units.

The result is a filter network that is (potentially) way more accurate in its operation, and delivers a better integrated and optimised sound.

Each separated frequency band of this line-level signal is then sent to a dedicated power amp that feeds as many drive units as are responsible for delivering those frequencies.

Active vs passive speakers: which is better?

On paper, active speakers have a whole host of advantages. Their crossover design gives the designer much greater control over the signal and is far less prone to losses and distortion when compared to a passive filter alternative.

As the power amplification is integrated into the design, it can be optimised for a specific drive unit. Because it’s normally built into the box, there’s no need for long lengths of speaker cable between the two, avoiding any distortion or loss caused by the wires. Simply put, there’s more grip and better control.

These benefits would seem to give active speakers a generous edge, but there are also downsides. There aren’t many speaker manufacturers that can make amplification, so the usual path is to buy in modules from an OEM supplier. There’s nothing wrong with this in principle, but things often fall short when it comes to implementation. The result is that the sound performance of the final active speaker is rarely as good as it could be.

Active speakers suffer in terms of perceived value on the shop floor too. Their electronics tend to be hidden, yet there will be an obvious price premium over similar-looking passive alternatives. Break down the respective costs and it usually turns out that the active option is the better value route, as it consists of multiple power amplifiers – a simple two-way speaker still needs four mono power amps – whereas a passive set makes do with a single stereo amp to work its four drive units.

Active designs also limit the amount of upgrading possible. You can’t just change the power amps, for example, the whole lot has to go. That leaves less scope for enthusiasts to mix and match. You either accept the power amplifier/speaker combination as a whole or you don’t.

How about active speakers with streaming?

While active speakers have clear performance benefits, their conciseness also means they are attractive to users looking for a more discreet and compact way to listen to music.

Increasingly we are seeing active speakers that aim to pack in even more functionality into their cabinets – not just amplification but also streaming modules and physical connections – creating a complete ‘all-in-one’ system that minimises the need for extra boxes or cabling. With features like preamp capabilities, digital and analogue inputs, Bluetooth and wi-fi streaming compatibility combined directly into active speakers (or a small accompanying box that then communicates with them), they offer a neat, compact, minimal fuss alternative to a system of separates. The cost can work out more favourably than buying everything separately, too (although you shouldn’t necessarily expect the same performance from them as you would a similarly priced collection of class-leading separates).

Some active speakers with streaming like the B&W Formation Duo are fine examples of such all-in-one stereo speaker systems, whereas others like the Dali Rubicon 2 C come with replaceable connectivity modules (or ‘hubs’) that handle the source side of things, meaning they can be easily upgraded. After all, unlike speaker technology, streaming technology is anything but timeless.

Active speaker Examples.

Bowers & Wilkins | Formation Duo Active Speakers

Yamaha MusicCast 50 Active Speaker